T-4600-CAC 46 Gallon Fresh Water Holding Tank & CAC 12 volt Water Pump rv

Description: Class A Customs Listing Includes1 (One) Class A Customs 46 Gallon Fresh / Gray Water Holding Tank Part# T-4600 1 (One) Class A Customs 12 Volt Water Pump Part # CAC-WP-12V30Read Entire Listing Frequently Asked Questions At Bottom Before You Purchase Free Shipping (when offered) is for the 48 Contiguous U.S. only Check Ship-to Address is correct & complete - Lot # / Apartment # / Suite #Larger Items that don't fit in mailbox carrier may decide not to leave, you will need to arrange delivery with the carrier. Multiple Tracking Numbers eBay will only upload one tracking number per order. If you need the other tracking numbers send a message do not open a case as it is not necessary. **Pump Ships in Separate Box USPS Mail** Item Details Fresh / Drinking Water Safe BPA Free and MADE IN USA Class A Customs located in Elkhart, Indiana is the manufacturer of this item. Class A Customs does not carry BPA nor uses it in the manufacturing process. NSF Certified Materials Tank & fittings made from DOW NSF International NSF/ANSI Std 61 approved Medium Density Polyethylene (MDPE) Resin - Paperwork is located on our main site - * No NSF Logo in tanks UV-8 stabilization Complies with: U.S. FDA 21 CFR 177.1520 (c)3.1a Canadian HPFB No Objection Underwriters Laboratories Inc. EU, 10/2011 NSF International NSF/ANSI Std 61 (sec 4 & 5) Food Vendors You must verify requirements with health department where inspection will be made before purchasing. Codes vary by local health departments, not states, we are not aware of the codes. Forward the documents provided on our main site to your local health department before purchasing to be sure these tanks will pass your local inspection, this is your responsibility. * No NSF Logo in tanks Non-Pressurized Tank All water tanks we carry must be vented allowing air in and out during use, they are not pressurized tanks. Fresh or Gray Water Use ideal for food vendors and extra water storage Seamless One-piece seamless construction, no seams to burst Resistant Stain Corrosion and Rust Resistant Color Creamy White so you can see waterline through tank Tank Preparation Tanks are made in a warehouse light scratching, scuffs, or dust may be present on tanks and does not effect performance of tank. Sanitize each tank prior to use to remove any debris from the manufacturing process, wipe with a damp cloth to remove surface dust or scuffs. Installation & Plumbing Have a certified technician install all parts to prevent product damage and personal injury. Do Not Pressurize Tank A garden hose is a pressurized water line, do not make a secured connection to the water tank with a pressurized line this will void any warranty on the tank. Tanks need to be gravity feed, this allows for air to escape while the water is going into the tank, see Basic Plumbing Diagram in photos. Turning a garden hose on half way does not work because you can control the amount of water flowing but not the pressure in the line, leaving the tank to fill risks exploding the tank. Do Not over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads. Check our store for fill dishes, food grade fill hose and basic plumbing items. You will need to verify items needed, we are not aware of what you need. Mounting & Bracing Tank needs to be adequately supported, sit on level surface and braced to prevent movement during transit Do Not hang tank by ratchet straps, this is too thin and will not adequately support tank. Do Not place weight on tank, if you need to stack the tanks you will need a weight bearing shelf between them. Tank Measurements (+/- .25" on each measurement) 42" does not include fittings x 14" x 18" (rotate tank to change height or width) Average thickness 7/32" +/- Fittings Installed In Tank See Photos TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife TWO) .5" Female NPT Fitting - fitting is open Class A Customs Water Pump - **Pump Ships in Separate Box USPS Mail**12 Volt Power Supply Only - 110/115/220 volt such as in a house or generator will damage the unitFRESH Water use only - not for use with dirty water, salt water or fuel. Water in Pump from Factory Testing Model: CAC-WP-12V30Fresh Water Use Only Open Flow: 11.6LPM / 3.0GPM Amps: 4.0A Max Amps: 8.0A Shut Off Pressure: 45PSI/3.1 Bar Be sure to read booklet before installing. The pump can be mounted at the same level or below the water tank, it may be positioned above the water tank if needed as it is capable of a 6 foot vertical prime. Horizontal inlet tubing will allow priming to 30 feet. Consider a dry location to allow easy access if maintenance is required. The pumps should not be located in an area of less than 1 cubic foot unless adequate ventilation is provided. Excess heat may trigger the internal thermal breaker and interrupt operation. When the temperature drops the breaker will automatically reset and pump will run again. The pump can be mounted in any position if mounting the pump vertically the pump head should be in the down position. The mounting feet are intended to isolate the pump from the mounting surface, over-tightening, flattening or use of oversized screws will reduce the ability to isolate vibration and noise through the lines. Electrical The pump should be on a dedicated individual circuit protected by the specified fuse indicated on the motor label. A U/L, CE etc approved marine duty (ignition protected) switch rated at above 15AMPS is recommended and must interrupt current flow on the positive (+red) lead. The pump must be grounded to a known ground (battery). The ground wire must be the same size (gauge/Mm2) as the positive wire. Proper wire sizing is required for good pump operation, if the wire is too small low-voltage will affect the pump performance and could create a fire hazard. The total current draw on the circuit must not exceed 15AMPS. If the pump is used in conjunction with other components, overload current protection (fuse or circuit breaker) and wire size must be for the total amp requirements of all devices on the circuit. Plumbing We recommend at least 1 foot of .5" (1/2") i.d. flexible high pressure tubing to both ports. Ideally the pump's ports/strainers should not be connected to plastic or rigid pipe. The pump's normal oscillation may transmit through rigid plumbing causing noise and possibly loosen or crack components. Installation of a 50 mesh strainer such as 51S01 series is recommended to prevent foreign degrees from entering the pump. Hex/swivel barb fittings provide easy removal if maintenance or access is required. The fittings are designed with a "taper seal" creating a water tight connection when hand-tightened. Always secure barb tubing connections with properly sized stainless steel clamps to prevent leaks, never use Teflon tape or sealing compounds on threads. Sealer may enter the pump causing a failure failure due to foreign debris and is not covered under warranty. OEM Parts Have a certified technician install all parts to prevent product damage and personal injury. No retail box, no installation instructions. Please research before purchasing this item, online videos and installation help can be found by searching classAcustoms blog Payment & Shipping Information Free Shipping (when offered) is for the 48 Contiguous U.S. only Check Ship-to Address is correct & complete - Lot # / Apartment # / Suite #Larger Items that don't fit in mailbox carrier may decide not to leave, you will need to arrange delivery with the carrier. Multiple Tracking Numbers eBay will only upload one tracking number per order. If you need the other tracking numbers send a message do not open a case as it is not necessary. Manufacturer Warranty Warranty does not cover install by customer or non-certified technician. No warranty, guarantee or liability is stated or implied on any product beyond the manufacturer. Class A Customs is not responsible for any damages caused from the use of this or any product we carry. Manufacturer warranty covers manufacturer defect on manufacturer installed fittings and tank. Using this tank for any purpose other than fresh or gray water storage will void any/all warranty. Do Not use tanks for sewage or fuel. Please research before purchasing this item, online videos and installation help can be found by searching classAcustoms blog FAQ's and Item Help Question: I need a custom tank can you make it? Answer: We can manufacture custom tanks, however you would need to purchase a mold which ranges from $6,500 and up. Question: I need a ____ Water Tank, do you have other sizes? Answer: Yes, we manufacture several sizes of fresh and gray tanks as well as black/waste water tanks check our store for all sizes.

Price: 239.99 USD

Location: Elkhart, Indiana

End Time: 2024-11-20T16:38:39.000Z

Shipping Cost: N/A USD