SpeedyBee F405 V3 V4 Flight Control 3-6S BLS 50A/55A ESC for RC FPV Racing Drone

Description: SpeedyBee F405 V3/V4 FC ESC Stack 3-6S Lipo Flight Control BLS 50A/55A 4 in 1 ESC 30x30 Bluetooth for RC FPV Racing Freestyle Drone DIY PartsV3 Features:1. Configure your FC and ESC via BT: With the SpeedyBee app, turn your phone into an all-in-one configurator and tune your quad anytime, anywhere. Enjoy the easy way to fly with fully configuring your FC ESC wirelessly.2. Powerful 50A 4-in-1 ESC: Built with the robust BB21 MCU and large motor pads for easy soldering. Built with Japan-made filtering SMT capacitors +onboard TVS protective diode, brings a smooth flight experience.Real 50A output, ready for your baddest 6S motors.3. Onboard Battery Life Indicator: Built with a 4-level LED battery indicator, now you can fly anywhere worry-free - even without your lipo checker!4. Change Motor Directions Wirelessly: Finishing your latest build? Just replaced your motor after a crash? Take your smartphone out, and configure your motor direction wirelessly with the latest SpeedyBee app. Works for all BLHeli32 / BLHeli_S / BlueJay ESCs.5. 4 sets of LED Pads with Simple Switching: Need more visibility at night? Just solder up your LED strips and blaze the darkest trail you can find. With just one tap on the BOOT button, you can cycle through all different LED presets and pick the one you love!V3 Specifications:SpeedyBee F405 V3 30x30 Flight ControllerMCU: STM32F405IMU(Gyro): BMI270USB Port Type: Type-CBarometer: Built-inOSD Chip:AT7456E chipBLE Bluetooth: Supported. Used for Flight Controller configurationDJI Air Unit Connection Way:Two ways supported: 6-pin connector or direct soldering.BetaFlight Camera Control Pad: Yes(CC pad on the front side)Current Sensor Input: Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)ESC Signal:M1 - M4 on bottom side and M5-M8 on front side.Mounting: 30.5 x 30.5mm( 4mm hole diameter)Dimension: 41.6(L) x 39.4(W) x 7.8(H)mmWeight: 9.6gSpeedyBee BLS 50A 30x30 4-in-1 ESCFirmware: BLHeli_S JH50Continuous Current: 50A*4TVS Protective diode: YesESC Protocol: DSHOT300/600Power Input: 3-6S LiPoMounting: 30.5 x 30.5mm(4mm hole diameter)Dimension: 45.6(L)* 44(W)* 6.1mm(H)Weight: 13.8gV4 Features:1. The new V4 stack circuit design has been significantly optimized, with PCB copper thickness upgraded from 2 ounces to 3 ounces, and MOS transistors upgraded to higher specifications. The continuous current of a single circuit has been upgraded to a total of four circuits of 220A, and the peak current has been further increased to 280A for 10 seconds.2. Easily drive any of the most violent 6S motors. Add aluminum alloy heat dissipation fins to quickly evacuate MOS tube heat, making the output of the electrical regulator more stable.3. Using well-known brand power supply chips to independently power the onboard ICM42688P gyroscope, the anti surge capability is increased by 320%; Equipped with a 100uF ultra large filtering tantalum capacitor, it protects the gyroscope data from power interference and allows you to fully experience the pure beauty of flight!4. The F405 V4 flight control supports 8-way motors, so it can be used on your X8, Y6, fixed wing, and other models that require more than 4 motors. Now open the SpeedyBee app and adjust the parameters immediately.5. We suggest connecting the TX and RX of the EL RS receiver to the T2 and R2 of the flight control. When you both When using for DJI sky terminal, some ELRS receivers may not be able to be recognized by flight control normally. If this problem occurs, you need to connect the SBUS signal cable of the sky end cable Disconnect from flight control. You can use tweezers to pick out the SBUS cable head from the 6PIN cable terminal (Alternatively, cut the wire directly) and properly insulate the wire ends.V4 Specifications:SpeedyBee F405 V4 30x30 Flight ControllerMCU: STM32F405IMU(Gyro): ICM42688PUSB Port Type: Type-CBarometer: Built-inOSD Chip: AT7456E chipBLE Bluetooth: Supported. Used for Flight Controller configurationDJI Air Unit Connection Way:Two ways supported: 6-pin connector or direct soldering.Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)ESC Signal:M1 - M4 on bottom side and M5-M8 on front side.Mounting: 30.5 x 30.5mm( 4mm hole diameter)Dimension: 41.6(L) x 39.4(W) x 7.8(H)mmWeight: 10.5gSpeedyBee BLS 55A 30x30 4-in-1 ESCFirmware: BLHeli_S J-H-40Continuous Current: 55A*4TVS Protective diode: YesESC Protocol: DSHOT300/600Power Input: 3-6S LiPoMounting: 30.5 x 30.5mm(4mm hole diameter)Dimension: 45.6(L)* 44(W)* 8mm(H)Weight: 23.5gPackage Included:As you choose Note:Only the above package content, other products are not included.1.Due to the difference between different monitors,the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures.2.Due to the manual measurement and different measurement methods, please allow 1-3mm deviation.Thanks!Before purchase:1.All the goods are ready stock, we will arrange the shipment at once if we receive the order.2.Please read the item description, if you have any question, do not hesitate to contact us.3.No warranty,if you receive a defect item,please contact us at once with item picture.4.Use the vouchers for more saving.After purchase:1.If you are satisfied,please express your use feeling.2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems. If you receive a defect item,please contact us at once with item picture or video.

Price: 45.22 USD

Location: Shenzhen

End Time: 2025-01-05T08:49:51.000Z

Shipping Cost: 0 USD