Description: Plugger 10 Clear Masonry & Wood Acrylic Flat Sealer Plugger 10 Clear Acrylic Sealer for Masonry & Wood Surfaces Rainguard Plugger 10™ Acrylic Sealer is a versatile, high performance modified silicone acrylic clear water repellent and sealer for application on painted and unpainted, vertical or horizontal concrete, masonry, brick or wood surfaces. Plugger 10 has Rainguard's exclusive Micro-lok™ nano based technology for improved water repellent and stain resistant performance. On unpainted surfaces, Plugger 10™ helps keep moisture out and resists staining for easier cleanup. It can be used as a primer to seal previously painted or wood substrates. On painted surfaces, Plugger 10™ can help solve moisture problems with a clear, protective coating with little change in surface appearance. It can be used as a primer to seal previously painted or wood substrates. Plugger comes in both a 5-year 25% formula and a 3-year 10% formula, depending on the level of protection and length of warranty desired. Where is Plugger 10 used? Construction & Remodel Projects: Exterior building walls Homeowner projects: Exterior brick|stucco walls, decks, patios, porches, walkways, fences Why Plugger 10 Acrylic Sealer? Labor and material water repellent warranty available for 3 years Seals and binds chalked surfaces and improves adhesion of topcoat materials Helps prevent efflorescence Stain resistant May be applied to previously painted and properly prepared surfaces Easy to use Concentrates available that saves money, time and easier on the environment! Protects wood from swelling, shrinking or grain raising May be applied to concrete or stucco as curing agent to promote hardening 100% Eco-friendly: low VOC Minimal change in surface appearance, UV resistant - will not yellow TECHNICAL INFORMATION Color Clear, minimal change in appearance Sheen/Gloss Level Flat sheen Dry To Re-Coat 1 hour #Coats Recommended 1 (2 coats if especially porous) Back in-service time 2 hours walk on Application method Low pressure hand pump or airless sprayer Where Can it be Used All Interior|Exterior and Vertical|Horizontal painted and unpainted surfaces Apply to New Concrete 48 hours Low Application Temperature 40F|4.4C Surface & Air Base Water VOC Content <20 g/L Use on Material Concrete, brick, masonry, stucco, block. natural stone, EIFS, wood, painted surfaces Warranty Available 3 year material/labor standard – download warranty application to register, see DOCUMENTS tab above CERTIFICATION/TEST Leed 4.2 (1) point credit available Meets LEED and SQAMD low VOC requirements COVERAGE RATE SQUARE FEET/GALLON Porous masonry 60-100 Dense masonry 100-150 Succo/EIFS 150-200 Wood 175-200 Painted Surfaces 400 Fluted, scored block, raked joints Reduces coverage rates 20%-30% APPLICATION INSTRUCTIONS CONDITIONS PRIOR TO APPLICATION Temperature (surface|air) 40F to 90F (4.4C to 35C) and at least 5F above dew point Moisture of substrate Less than 15% Humidity Less than 90% Rain No rain 48 hrs prior to, 12 hrs after application Cure time for newly poured concrete Apply 48 hrs after pour Application method Use low pressure hand pump or garden sprayer WORKING WITH CONCENTRATES PART # SIZE MAKES INSTRUCTIONS CR-1502 32 oz 5 Gal Empty 32oz into 5 gal pail, fill with water, stir (19 parts water to 1 part Plugger 10) CR-1506PK 32 oz 30 Gal Case of 6 quarts CR-15-2 see that sku for instructions FOLLOW THESE SIMPLE APPLICATION STEPS Horizontal Concrete Surfaces Apply two saturation coats to damp concrete to assist the curing and hardening process. Apply one saturation coat to ex-isting concrete surfaces to dustproof surfaces. Remove excess standing or ponding materials with a roller. Caution: PLUGGER 25 is not recommended for application to surfaces subject to wheeled traffic. Brick Apply one saturation coat with run-down and back roll material. Apply second saturation coat when the first coat is dry. Stucco/Plaster May be applied to stucco or plaster during the curing process or when fully cured. Apply one saturation coat and back roll materi-als. Apply second coat when the first coat is dry. Chalked Surfaces Apply one coat to chalked surfaces. Allow material to dry and check surface for chalking. Apply a second coat to surfaces as needed to control remaining surface chalk. Wood Surfaces shall be clean and bare. Pre-treat knots with a small amount of material. Apply a minimum of one saturation coats to wood surfaces. Apply second coat when the first coat is dry. Masonry and Concrete All surfaces to be coated shall be structurally sound, clean, and dry, free of laitance, accumulated dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mor-tar, and mold and mildew, etc. Remove loose and peeling paint, excessive chalk, and other contaminants from surfaces. Dry brushing is the preferred method for cleaning surfaces prior to material application. However, chemical, mechanical, abrasive, or high-pressure water blasting may be used. Allow wet, cleaned surfaces to dry for 2-3 days before application of materials. EFIS and Other Surfaces Surfaces shall be structurally sound, clean, and dry. Clean EFIS surfaces following manufacturer’s recommendations. PRECAUTIONS & LIMITATIONS 1. All surfaces to be coated should be clean of any dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mortar, and mold and mildew, etc. 2. All cracks should be pointed or caulked. All voids, bee holes, masonry surface defects and openings such as conduits, pipes, drains, door frames, vents, air conditioner openings, electrical openings, control joints, or any dissimilar materials should be repaired using urethane or other approved patching. STORAGE Store materials in a well-protected area between 45° and 90°F. Avoid freezing temperatures, direct sunlight, and moisture. Keep away from heat sources. Size Condition Price Concentrate - Makes 5 Gallons New 144.90 Ready-to-Use 1 Gallon New 52.90 Ready-to-Use 5 Gallons New 188.60 Shipping Shipping cost:No cost shipping lower 48 US States FedEx Ground Delivery time:Typically 3-5 days to process order plus 1 to 5 days transit time after shipment depending on location Payment We accept the following payment methods: PayPal payment due at time of order placement Please contact us if you have any questions. Service PLEASE CONTACT CUSTOMER SERVICE FOR QUESTIONS
Price: 52.9 USD
Location: Costa Mesa, California
End Time: 2025-01-18T00:54:42.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: Rainguard
Color: Clear
Sheen: Flat
Surface Applied To: Block, Concrete, Pavers, Stone, Wood
Product Material: Acrylic
Warranty: 3 Year Labor & Material Warranty
UPC: 6 6004100119 2, 6 6004199989 5, 6 6004199996 3
Type: Does not apply
Available Variations
Color: Concentrate - Makes 5 Gallons
Price: 144.9 USD
Available Quantity: 6
Quantity Sold: 0
Color: Ready-to-Use 1 Gallon
Price: 52.9 USD
Available Quantity: 6
Quantity Sold: 0
Color: Ready-to-Use 5 Gallons
Price: 188.6 USD
Available Quantity: 6
Quantity Sold: 0