Description: Description Peak 1000W Class D Power Amplifier Board Mono Power Amp Board with Switching Power Supply Function Introduction: 1. Power supply AC220V can also be set to AC110V 2. Size: 200 x 130 x 42mm/7.9 x 5.1 x 1.7" (LxWxH) 5. Peak power 1000W, 4 ohm load 6. RMS power: 500W, 4 ohm load 7. RMS power: 300W, 8 ohm load 8. Channel: Mono 9. Voltage output for preamplifier +15v, 0V, -15V 10. Fan voltage output +24V Specifications: 1. Amplifier model: J115D-AMP 2. Amplifier type: Class D digital amplifier (switching power supply) 3. Board color: Blue 4. Channel: Mono (not stereo) 5. Can be bridged: NOT 6. Peak power: 1000W 7. RMS power: 500W, 4 Ohm load (one 4 Ohm speaker) 8. RMS power: 300W, 8 Ohm load (one 8 Ohm speaker) 9. RMS power: 500W, 8+8 Ohm load (two 8 Ohm speakers used in parallel) 10. Frequency response: 20HZ-20KHZ at -2DB 11. Distortion: THD ≤1% at 1KHZ (4 ohms) 12. Board Size: 200 x 130 x 42mm/7.9 x 5.1 x 1.7" (LxWxH) 13. Net weight: 0.8KG/1.8LB 14. Input working voltage: AC100-120V 60HZ, CP3 and cp4 connection 15. Input working voltage: AC200-240V 50HZ, CP3 and cp4B are not connected 16. Input working voltage error: +/-10% 17. Need to add 24v fan: Yes 18. Amplifier main power supply voltage: +79V, 0V, and -79V 19. Output voltage for preamplifier board: +15V, 0V, and -15V 20. Fan output voltage: 24v 21. Input sensitivity: Amplitude: 1.5V; Frequency: 1KHZ; Waveform: Sine wave 22. Magnification: 30 times 23. Signal input ports: IN (signal input) and G (signal ground) 24. Speaker port: SPK- and SPK+ 25. Power port: AC INPUT L and N 26. Noise: ≤1 MV 27. The speaker has output short-circuit protection: Yes (automatic reset after removing the short circuit) 28. Boot delay anti-shock sound 1-3 seconds Package Included: - 1 x Power Amplifier Board Attention: This power amplifier board is an integrated board of digital power amplifier and switching power supply. Tips: 1. AC N and AC L: Power input AC 210-230V. Do not exceed the supply voltage range. 2. AC N and AC L: AC power supply input. Can be changed to 110v power supply. After modification, the 220V power supply cannot be used again. 3. AC100-115V working status: connect any pin of CP3 to any pin of CP4 4. AC200-240V: CP3, CP4 OPEN 5. P1 +24v and G pins are connected to 24v fan. Pay attention to the polarity of the fan, do not connect it in the opposite direction. The fan interface cannot be short-circuited, otherwise it will cause a fault and the device to not work! 6. Because the power of the power amplifier is large, the board needs to be dissipated when it is working. When no load, the board also needs to dissipate heat. A heat sink needs to be installed for heat dissipation. There are many other heating elements, such as transformers, output inductors, large resistors, large capacitors, and ballast bridge stacks. These components also require fans to dissipate heat. It is recommended that a fan blows air from the amplifier section to the power supply section. 7. There are four output ports. Every two terminals are connected in parallel, and any terminal can be connected to speakers. SPK- and SPK+ are load outputs, connect to speakers with a load of 4 ohms to 8 ohms. Do not connect speakers with a load of less than 4 ohms. 8. The auxiliary power supply of the P2 socket outputs +15V/-15V at 500MA to the preamp, and cannot be used for overloading. Also, it can not connect to the input voltage. It is only output to the preamplifier board. 9. G in of P2 socket is the signal input. Among them, G represents GND, which is also the negative pole of the signal input; in represents the positive pole of the signal input. Please pay attention to the polarity when connecting, do not reverse the connection. When the maximum input signal is 1.5V, its output power reaches the maximum value, which cannot exceed the input 1.5V, so as not to damage the power amplifier due to overload. 10. Input signal cable should preferably be shielded to avoid interference. Do not hot-plug the signal input. It is not recommended to connect to mobile phone signal. 11. AC power supply is high voltage and cannot be tied together with the bass wire. AC input is high-voltage power, which cannot be tied together with the signal input, auxiliary power +/-15 output, and speaker output wire. 12. Do not tie the signal input with the speaker wire, so as not to cause high-frequency self-excitation and damage the power amplifier. 13. The switching power supply is charged with high voltage, so remember not to touch the high voltage part with your hands. 14. If D12 lights up red, it means there is a short circuit in the power amplifier part. This could be because of a shorted fan, a shorted preamp, or the broken amplifier. 15. If the temperature of the heat sink exceeds 85°C, the power amplifier will automatically turn on the protection function and stop working. After waiting for the temperature to drop, it will start automatically. Payment Terms 1. We accept PayPal,Payoneer,Visa Card,Google pay,Credit card etc. 2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay. Shipping Terms 1. We will process the order within the handling time ,if you have any questions, please contact us via eBay message or email. 2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding. Return Terms If you receive the item that not satisfied or defective, please do not open case and kindly notify us within 30 days. We will guide you the returning process for replacement or refund. Custom Duties & Taxes 1. It is buyers responsibility to cover the import duties, taxes.We do not charge any taxes and fees, and the possible taxes and fees will be collected by the platform or by third parties such as customs and carriers. 2. Please check with your countrys customs office and inform us what/how much should declare before shipping. Feedback 1. Please kindly leave us a positive feedback and 5 star DSR if you satisfied with our product and service. Please feel free to contact us firstly if you have any problem with your order, we are responsible and credible seller and will solve the issue it for you asap. 2. If you are dissatisfied for any reason, please dont be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers. On Jul 4, 2023 at 18:49:27 PDT, seller added the following information:
Price: 65.99 USD
Location: California
End Time: 2024-02-05T02:44:28.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Return shipping will be paid by: Seller
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Return policy details:
Compatible Brand: Universal
Type: Board
Color: Blue
Channel: Mono (not stereo)
Country/Region of Manufacture: China
Amplifier model: J115D-AMP
Amplifier type: Class D digital amplifier (switching power supply)
Peak power: 1000W
Amplifier Class: D
EAN: Does not apply
UPC: Does not apply
ISBN: Does not apply
Brand: Unbranded
MPN: Does not apply