Description: This is a used MKS 625H13TCEEU Baratron Capacitance Manometer. It was in good working order before being harvested from the donor tool. It will need to be zero calibrated once installed, please refer to the manufacturers website for proper calibration instructions. If there are any problems with this unit, please don't hesitate to send us a message so we can remedy the situation with a return/refund. We want to provide our customers with the best service and parts. We buy our inventory from local precision manufacturers within the semiconductor community to ensure quality and OEM performance standards. For custom quantities, please send us a message inquiry and we can get you a quote. If there are any issues with your order, please reach out and we will be glad to help. How To Adjust the Zero All pressure transducers require initial and periodic zero adjustments. Prior to initial operation and during periodic maintenance you must check the transducer zero to verify the proper output. The zero can be set (or reset) by adjusting the ZERO potentiometer located on the top of the transducer or at the front panel of any MKS Power Supply/Readout being used. If the ZERO potentiometer fails to provide sufficient adjustment, the COARSE ZERO switch may be used. To achieve the full dynamic range specified for the transducer, the zero adjustment must be made at a pressure less than the transducer’s resolution (0.001% of FS). Low range transducers should be pumped for at least one hour after exposure to air to remove any moisture and to allow the pressure to stabilize. Zeroing a transducer above its stated minimum resolution creates a zero offset relative to true absolute pressure. All subsequent readings are then linear and accurate relative to the offset value. OverviewThe 625H13TCEEU Heated (100°C) Absolute Baratron® Capacitance Manometer with Trip Points features 1000 Torr full scale pressure measurement, a female 8 VCR type fitting, and 15-pin D-subminiature electrical connector. It has two user adjustable process trip point relays, each with an adjustment range from 0.1% to 100% of Full Scale or voltage equivalent 0.01 to 10 VDC. Dual color LEDs indicate relay status. Typical relay uses include pump cross-over and valve activation. The 625H operates with ±15 VDC (±5%) input at <600 mA, and provides an output of 0 to 10 VDC linear with pressure. The 625H sensor exposes only Inconel® to the process permitting the use with corrosive or dirty gases. Measurements are independent of gas composition. The modern stainless steel enclosure provides a cleanroom compatible product. Technical SpecsTypeVacuum/pressure TransducerMeasurement TypeAbsoluteSensor Temperature100°CFull Scale Range1000 TorrAccuracy0.25% of ReadingResolution0.001% of Full ScaleFitting Type8 VCR femaleAnalog Output0-10 VDCAnalog Connector15-pin D-sub with Thread LocksZero Temperature Coefficient0.002% of Full Scale/°CSpan Temperature Coefficient0.02% of Reading/°COperating Temperature Range15-50°CVolume6.3 ccWarm-up Time2 hoursOverpressure Limit45 psia (310 kPa)Exposed MaterialsInconelPower Requirements±15 VDC ±5% @ 0.60 Amps (max.)Trip Points2Trip Point Level Signal0.01-10 VDC for each trip pointRelay Contact RatingsSPDT, 1 Amp @ 30 VDC or 0.5 Amp @ 30 VAC resistiveComplianceCE
Price: 299.99 USD
Location: Hillsboro, Oregon
End Time: 2024-11-08T05:11:15.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: MKS Instruments
Unit Type: Unit
Air Pressure Range: 1000 Torr
MPN: 625H13TCEEU
Country/Region of Manufacture: United States
Unit Quantity: 1
