Miss Selfridge

Matek M10Q-5883 GNSS & Compass module

Description: The Matek M10Q-5883 GNSS & Compass Module provides a reliable and accurate GNSS and Compass solution to meet all your navigation needs. The powerful, multi-band receiver supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou) systems.  With high numbers of visible satellites, this module maximizes positional availability in the most difficult of situations. Whether you need to track a vehicle, boat, drone, or robotic arm, the Matek M10Q-5883 is the perfect tool for accurate navigation. Features: M10Q-5883 uses multi-constellation GNSS module powered by u-blox SAM-M10Q-00B. The SAM-M10Q features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. SAM-M10Q supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes the position availability, in particular under challenging conditions such as in deep urban canyons. u-blox Super-S (Super-Signal) technology offers great RF sensitivity and can improve the dynamic position accuracy in non-line-of-sight scenarios. The high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation. More details about the SAM-M10Q, pls check out u-blox SAM-M10Q page Specifications: GNSS u-blox SAM-M10Q-00B (GPS, GLONASS, Galileo and BeiDou) Magnetic Compass QMC5883L Patch antenna 15*15*4mm Input voltage range: 4~9V (5V pad/pin) Power consumption: 13mA UART baudrate: 9600 default Operating Temperatures: -20~80 °C UART(TX, RX) interface for GNSS SAM-M10Q-00B I2C(DA, CL) interface for Compass QMC5883L JST-GH-6P connector (SM06B-GHS-TB). 1.27mm pitch GNSS PPS LED, Green. (Solid ON after powering on,  blinking(1Hz) when GNSS get 3D fix) Protocol: UBX(u-blox)  5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz 20mm*20mm*12.4mm 8g M10Q-5883_step.zip Tips and Notes: Compass Alignment(flat mounting): Tilting the magnetometer is strongly discouraged ! INAV/BetaFLight: compass Arrow forward, set CW 270° Flip when flight controller arrow is facing forward. INAV/BetaFLight: compass Arrow backward, set CW 90° Flip when flight controller arrow is facing forward. Ardupilot/Mission Planner: Rotation None. Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron based material ——————– INAV 5.0.0, Betaflight 4.3.0,  ArduPilot 4.3 or newer is required. UBlox NEO-M9N, MAX-M10S, SAM-M10Q series all don’t have dataflash built in.  once GNSS is powered off and the supercapacitor run out. the settings will back to default. UBX protocol is bidirectional.  Flight controller firmware can change settings on GPS via UBX protocol. You don’t need to set GNSS module parameters in u-center. The default configuration on SAM-M10Q with ublox FW 5.1 is concurrent reception of GPS, Galileo, GLONASS, and BeiDou B1C with QZSS and SBAS enabled. Start with u-blox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed. The M10Q-5883 provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can’t detect the GNSS module(grey GPS icon), try doing reset. The scratches on ceramic antenna are the result of tuning the antenna. Troubleshoot GPS related issues: http://www.mateksys.com/?p=5712#tab-id-6 u-center Windows Includes: 1x Matek M10Q-5883 GNSS & Compass module 1x JST-GH-6P to JST-GH-6P 20cm silicon wire

Price: 45.99 USD

Location: Madison, Alabama

End Time: 2024-11-30T02:37:58.000Z

Shipping Cost: N/A USD

Product Images

Matek M10Q-5883 GNSS & Compass moduleMatek M10Q-5883 GNSS & Compass moduleMatek M10Q-5883 GNSS & Compass moduleMatek M10Q-5883 GNSS & Compass module

Item Specifics

Return shipping will be paid by: Seller

All returns accepted: Returns Accepted

Item must be returned within: 30 Days

Refund will be given as: Money back or replacement (buyer's choice)

Return policy details:

Brand: Matek

MPN: ced-40569829064773

Recommended

Matek ASPD-4525 Digital Airspeed Sensor
Matek ASPD-4525 Digital Airspeed Sensor

$54.00

View Details
5” Carbon Fiber Quadcopter-DX2205 LHI Motors-Matek-4 ESC’s-Carbon Fiber Props.
5” Carbon Fiber Quadcopter-DX2205 LHI Motors-Matek-4 ESC’s-Carbon Fiber Props.

$99.99

View Details
3Pcs Matek Systems Micro BEC 6S IN 6-30V out 5V/9V-ADJ for RC FPV Racing Drone
3Pcs Matek Systems Micro BEC 6S IN 6-30V out 5V/9V-ADJ for RC FPV Racing Drone

$14.09

View Details
Matek mR900-30-TX mLRS MAVLink 900MHz TX Module Kit
Matek mR900-30-TX mLRS MAVLink 900MHz TX Module Kit

$39.99

View Details
MATEK BEC12S-PRO 9-55V TO 5V/8V/12V-5A Voltage Regulator BEC Module For RC Drone
MATEK BEC12S-PRO 9-55V TO 5V/8V/12V-5A Voltage Regulator BEC Module For RC Drone

$21.61

View Details
Matek Systems PDB Power Distribution Board XT60 BEC 5V & 12V 2oz
Matek Systems PDB Power Distribution Board XT60 BEC 5V & 12V 2oz

$8.81

View Details
Matek CRSF to PWM Converter
Matek CRSF to PWM Converter

$13.99

View Details
Matek Digital Airspeed Sensor ASPD-DLVR AP_Periph CAN Pitot tube
Matek Digital Airspeed Sensor ASPD-DLVR AP_Periph CAN Pitot tube

$10.00

View Details
Matek Systems LED & POWER HUB 5 IN 1 V3 5IN1V3
Matek Systems LED & POWER HUB 5 IN 1 V3 5IN1V3

$4.95

View Details
MATEK SYSTEMS HUBOSD Eco H-Type w/ STOSD8 Sensor & Dual BEC 6193
MATEK SYSTEMS HUBOSD Eco H-Type w/ STOSD8 Sensor & Dual BEC 6193

$29.99

View Details