Kit Flywheel + Stator fits Polaris Ranger 500 Series 11 2004

Description: Free shipping in USA Same day shipping visit our store > find parts for : ATV / UTV / SXS Motorcycles Snowmobiles Watercraft Other Menu Store Home find parts for ATV / UTV / SXS Motorcycles Snowmobiles Watercraft Other IMPORTANT - Important notice about the product.--> Kit Flywheel + Stator for Polaris Ranger 500 Series 11 2004 | OEM # 3084974 KEY FEATURES Brand New Stator + Flywheel Kit Direct replacement to your original unit Plug-and-play, direct fit, easy installation All item pictures are accurate All products shipped are tested DESCRIPTION Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced. There are more than one possible stator that can match with this flywheel, please compare your part with our picture. The other stator is in the kit flywheel + stator RMS900-104042. Brand new aftermarket Stator + Flywheel Kit Brand new stator Direct replacement to your original unit Plug-and-play, direct fit, easy installation Highest grade of lamination materials Highest grade of copper winding, resistant to 200 degrees Celsius Pick up pulsar coil included Connector included Rubber grommet included All shipped products are tested *All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part. Don't Repair. Replace like a pro! New Heavy Duty Flywheel Rotor Polaris 400 & 500cc ATVs --> Introducing our newest Heavy Duty Flywheel Rotor For Polaris 400 & 500cc ATVs. Anyone who rides or repairs the Polaris 400 & 500cc ATVs is probably familiar with the flywheel problems common to these models. Most of these bikes will have at least one flywheel failure in their lifetime so far. Low quality epoxy was used on OEM flywheels to secure the magnets to the rotor body. Over time and many heat cycles, the epoxy fails allowing the magnets to come loose and contact the stator, potentially causing catastrophic damage. For years, service shops & dealerships have offered low cost repairs for Polaris flywheels to save the 400$+ OEM replacement. This sounds like a great idea at first, but there are some serious issues! The common repair is using JB Weld? Marine Blue Epoxy to reattach the loose original magnets, or to install new ones. Epoxy fixes do repair flywheels in short term, if they are done correctly. However, this kind of repair can easily cause immediate problems, and impact long term reliability of your ATV. --> A Heavy Duty Flywheel to the rescue! New RMSTATOR heavy-duty flywheel rotor for Polaris ATVs is a well-priced solution to problems with the OEM flywheel, and an excellent alternative to all the mechanical troubles you can encounter with a repair. Features Built to OEM sizeFits precisely in your ride: install it and forget it. Improved epoxyUses high temperature epoxy that is stronger than OEM, eliminating the possibility of magnet detachment. High grade steel capping Prevents harsh additives in motor oil from degrading the epoxy attaching the magnets. Though extremely unlikely, if a magnet did ever come loose, it would remain in the sleeve preventing contact with the stator. Precise balancingEliminates crankshaft vibrations for longer engine longevity. Shop with confidenceOne year warranty. All products are tested. Don't waste time with temporary solutions, and start fixing your ride like a pro! Why cheap repairs won't work? Quick stronger epoxy fixes do repair flywheels in short term. It might however impair long term performance and reliability of your ride. Remaining OEM magnets: Original magnets remaining can still come loose at any time. Magnet alignment:The alignment of magnets around the flywheel is critical for proper stator operation. Even very fine misalignment will reduce stator efficiency significantly. Magnet spacing:Excessive epoxy or incorrect magnet spacing around the flywheel can easily affect the flywheel balance. This can cause stator contact or even crankshaft damages. Incorrect replacement magnets:The magnetic field strength of new magnets MUST match the originals. Stator failure can occur quickly with stronger magnets and stator output can be decreased significantly using weaker magnets. Wrong epoxy properties: Epoxy that is not rated to permanently handle high temperatures and oil immersion can quickly cause a serious failure. Oil contamination:Wrong epoxy for the application can also contaminate the crankcase oil, damaging the motor. All these reasons make us strongly recommend that you replace your broken flywheel with a new 400+ OEM one or our new heavy duty flywheel. PAcked with these technologies --> Vehicle models fitment Polaris Ranger 500 Series 11 -- 2004 OEM part replacement 104043-R00 Specifications Flywheel : Dimensions: Exterior Diameter: 130 mm Interior Diameter: 116 mm Interior Diameter Center Housing: 24.50 mm Exterior Diameter Center Housing: 22.50 mm Thickness (exterior): 44.70 mm Thickness (interior): 40 mm Stator : Dimensions : Interior diameter : 42 mm Exterior diameter : 105 mm Thickness : 32 mm Length of wires stator to grommet : 140 mm Length of wires grommet to plug : 1000 mm Length of pickup coil's wire to grommet : 170 mm Other specifications : Number of wires : 9 Number of plugs : 7 Number of pins : 12 Wire to wire resistance : Alternator : Yellow to Yellow/Red = 0.4 ohms +/-20% Pickup : White/Red to White = 115 ohms +/-20% Source : Black/Red to Green = 45 0ohms +/-20% Source 2 : Red to Green = 4.1 ohms +/-20% instructions Flywheel : Before attempting to start your Polaris vehicule adjusting the air gap is necessary. Rotate the flywheel so the raised node is lined up with the pick up/pulser coil and adjust as close as possible but no less than 0.010". Before installing your new stator Stator : Check the AC output of the stator. Replace any burned or corroded connectors on stator and regulator/rectifier Check and repair any melted wiring. Use hi-temp dielectric grease on all connectors Our stator may use a different wire color code than your original. All of the wires are installed in the correct order; please do not change any of the wiring configurations. This stator is designed as a direct plug-in replacement and should be used as such. When bolting stator in, always use locking compound. If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010". SHIPPING We deliver 99.4% of our orders within the specified time period. If your item is not available in our main Colorado facility, we still guarantee that your order will be delivered within the specified time period. If your item is not delivered within this time period, we will offer you a 5.00$ discount on your order. This guarantee applies to shipments delivered in the 48 continental USA states, excluding PO boxes. Videos Racetech around the world --> customer service AsK seller a question duties & taxes International Buyers: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. RaceTech Electric was founded in 2011 by three motorcycle industry veterans in San Diego, CA. The group has over 20 years combined in the Motorcycle industry. Customer servicePart request About usAbout seller pageAdd seller to favorite

Price: 493 USD

Location: Dover, New Jersey

End Time: 2024-11-24T19:29:08.000Z

Shipping Cost: 0 USD