FPV Quadcopter Drone 10" 6-12S TBS Crossfire DJI O3 Professionally Built + Tuned

Description: Hello everyone and thanks for checking out my INSANE 6S-12S 10" Ultra Versatile Quadcopter! This is a really unique Quadcopter and as always I'm going to start with a list of all the major parts: Frame- GepRC Pulsar LR-10GEP-Pulsar LR10 Frame - GEPRC VTX- DJI O3 Air UnitDJI O3 Air Unit - Go the Distance - DJI Camera- DJI O3PDB- Mateksys XCLASS PDB FCHUB-12SPDB FCHUB-12S for XCLASS – Matek Systems Quick Start Guide (PDF)PDBInput voltage range: 8~60V (3~12S LiPo)4x70A cont, 4x110A burst4x ESC power /signal/ telemetry padsCurrent Senor: 440A, 3.3V ADC, Scale 752x LED indicators for 5V, 12V1K:20K voltage divider built-inJST-SH 8pin connector“V” pad: 12V or VBat voltage selectableG: GNDCurr: current sensor signalTLM: for BlHeli32 ESC telemetryS1~S4: ESC signalBEC 5V output (5V pad)Voltage: 5.1 +/- 0.1VDCContinuous current 5 Amps, Max.6AShort-circuit tolerant (2 seconds)Overcurrent protection & self-recoveryBEC 12V output (12V pad)Voltage: 12.0 +/- 0.2VDC (Input voltage >=12V)Continuous current 4 Amps, Max.5AInput voltage<12V, Output voltage = Input voltageShort-circuit tolerant (2 seconds)Overcurrent protection & self-recoverySwitchable 12V output (12VSW pad)12V ON/OFF switchable via PINIO(high/low level)support constant 2Acan be use for powering VTX,LED etc.BEC 3.3V outputLinear RegulatorContinuous current: 500mAPhysicalMounting: 30.5 x 30.5mm, Φ3mmDimensions: 55 x 50 x 6 mmWeight: 21gIncluding1x FCHUB-12S V21x SH1.0_8pin cable 5cm, 2x SH1.0_8pin connectorsFlight Controller: Mateksys H743 Slim V3 Flight Controller H743-SLIM V3 – Matek Systems FC SpecificationsMCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB FlashBoard V1.0 IMU: MPU6000 (SPI1) & ICM20602 (SPI4)Board V1.5 IMU: MPU6000 (SPI1) & ICM42605 (SPI4)Baro: Infineon DPS310 (I2C2)OSD: AT7456E (SPI2)Blackbox: MicroSD card socket (SDIO)7x Uarts (1,2,3,4,6,7,8) with built-in inversion.13x PWM outputs(including “LED” pad)2x I2C1x CAN6x ADC (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2)3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)1x SPI3 breakoutUSB Type-C(USB2.0)1x JST-SH1.0_8pin connector (Vbat/G/Curr/Rx8/S1/S2/S3/S4)1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G)Dual Camera Inputs switch5V/Vbat filtered power ON/OFF switchDJI FPV OSD is supported by any spare UARTPowerVbat Input: 6~36V (2~8S LiPo)BEC: 5V 2A cont. (Max.3A)LDO 3.3V: Max.200mANo Current Sensor built-inADC Vbat2 pad supports Max. 69V (voltage divider: 1K:20K)Static power: 200mA@5V with Betaflight, 150mA@5V with ArduPilotFC FirmwareArduPilot(ChiBiOS): MATEKH743BetaFlight: MATEKH743INAV: MATEKH743PhysicalMounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mmDimensions: 36 x 36 x 5 mmWeight: 7gIncluding1x H743-SLIM6x Silicon grommets M4 to M31x JST-SH1.0_8pin cable, 5cm2x JST-SH1.0_8pin connectors1x JST-GH-4P to JST-GH-4P cable for CAN port, 20cmGPS: Mateksys qmc-5883GNSS & Compass, M10Q-5883 – Matek Systems M10Q-5883 uses multi-constellation GNSS module powered by u-blox M10 seriesThe GNSS module features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. It supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the best signals. This maximizes the position availability, in particular under challenging conditions such as in deep urban canyons. u-blox Super-S (Super-Signal) technology offers great RF sensitivity and can improve the dynamic position accuracy in non-line-of-sight scenarios.The high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation.SpecificationsGNSS u-blox M10 series (GPS, GLONASS, Galileo and BeiDou)Magnetic Compass QMC5883LPatch antenna 15*15*4mmInput voltage range: 4~9V (5V pad/pin)Power consumption: 13mAUART baudrate: 9600 defaultOperating Temperatures: -20~80 °CUART(TX, RX) interface for GNSSI2C(DA, CL) interface for Compass QMC5883LJST-GH-6P connector (SM06B-GHS-TB). 1.27mm pitchGNSS PPS LED, Green. (Solid ON after powering on, blinking(1Hz) when GNSS get 3D fix)Protocol: UBX(u-blox) 5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz20mm*20mm*12.4mm8gM10Q-5883_step.zipIncludes1x M10Q-58831x JST-GH-6P to JST-GH-6P 20cm silicon wireWiring and settingsM10Q-5883 5V to Flight controller 4~9VM10Q-5883 RX to Flight controller UART_TXM10Q-5883 TX to Flight controller UART_RXM10Q-5883 CL to Flight controller I2C_SCLM10Q-5883 DA to Flight controller I2C_SDAM10Q-5883 G to Flight controller GNDTips and NotesCompass Alignment(flat mounting): Tilting the magnetometer is strongly discouraged !INAV/BetaFLight: compass Arrow forward, set CW 270° Flip when flight controller arrow is facing forward.INAV/BetaFLight: compass Arrow backward, set CW 90° Flip when flight controller arrow is facing forward.Ardupilot/Mission Planner: Rotation None.Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron based material——————–INAV 5.0.0, Betaflight 4.3.0, ArduPilot 4.3 or newer is required.UBlox NEO-M9N, MAX-M10S, SAM-M10Q series all don’t have dataflash built in. once GNSS is powered off and the supercapacitor run out. the settings will back to default.UBX protocol is bidirectional. Flight controller firmware can change settings on GPS via UBX protocol. You don’t need to set GNSS module parameters in u-center.The default configuration on M10 GNSS with ublox FW 5.1 is concurrent reception of GPS, Galileo, GLONASS, and BeiDou B1C with QZSS and SBAS enabled.Start with u-blox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed.The M10Q-5883 provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can’t detect the GNSS module(grey GPS icon), try doing reset.The scratches on ceramic antenna are the result of tuning the antenna.Troubleshoot GPS related issues: https://www.mateksys.com/?p=5712#tab-id-6u-center WindowsMotors: Demon Power Systems Surge H.O 3120 Beast Class Motor Description: The New "Surge H.O" motor introduction to the Demon Power Systems lineup! This "little" brother to the already popular 4220 Omen series motor is perfect for your Beast Class/ X-Class build!Specifically designed for 8"-10" props the "Surge" Beast class motor is in the F1 class of performance, speed and ultra light. Designed for high output applications. Specifically designed with a one piece bell made from 7075 t-6 aluminum for durability and excellent cooling. If you want the best performance of your craft this is it! Specs: -H52 Arc Magnets-.15 stator Laminations-Titanium 5mm hollow shaft-Japanese NMB bearings-Bell: 7075 t-6-Magnet configuration: 12N14PH.O. (high output) Tech specs:-Ultra high temp 320C (500 F) coating and high density copper windings.-additional cooling area on main rotor and base-16 gauge motor wire-7075 T-6 aluminum Head and base-High efficiency stator laminations-Hi temp Arc magnets-Keyway lock in hub for all propeller types. -Wire protected base plate -Stator size: 31 wide x20 high-Motor weight: 129g no wires -Triple bearing for extreme durability and longevity. ESC'S: Flycolor X-Cross HV3 80A 5-12S BLHeli32 ESC X4About this productThe X-Cross HV3 80A 5-12S ESC by Flycolor features quality MOSFETs, BLHeli_32 firmware, an ARM 32-bit Cortex MCU, Telemetry, and more!FeaturesARM 32-bit Cortex MCU, frequency up to 64MHzInternational famous brand MOSFET with high performance and low ESR, not afraid of large currentBL Heli_32 firmware, u0 to 12S Lipo, suitable for X Class frame droneSupports regular 1-2ms pulse width input, as well as Oneshot125, Oneshot42, and Multishot.The input signal is automatically detected by the ESC upon power-upSmall size, lightweight, suitable for the drone with narrow armsDamped light does regenerative braking, and inherently also does active freewheelingThe silicone twisted-pair of the throttle signal cable effectively reduces the crosstalk caused by signal transmission and makes flight more stableAluminum heatsink effectively slows down the temperature riseSpecificationsCon. Current: 80ABurst Current: 100ALipo: 5-12SWeight: 25.5gSize: 55×28×10mmIncludes1 x Flycolor X-Cross HV3 80A 5-12S BLHeli32 ESC More InformationSKU13502UPC (GTIN)751313218155ManufacturerFlyColorNDAA CompliantNoMounting PatternSingle Arm ESCItem ReturnsThis item can be returnedProducts Related To This ItemFrSky FrESC32 BL_Heli32 80A 3-6s ESC$41.99T-Motor Alpha 80A HV ESC$130.99T-Motor Flame 180A HV ESC$259.99Lumenier Razor LED 55A 4-in-1 F3 BLHeli_32 2-6s ESC$61.99APD HV_Pro 24S 200A 180MHz 32-Bit ESC$1,299.00APD F-Series 40F3 6S 40A 32-Bit ESC$29.00APD F-Series 200F3[X] 14S 200A 60V 32 Bit ESC$209.00V-Good RC 32-Bit 80A 2-6S Brushless ESC for RC Airplane$33.99 Propellers: HQProp MacroQuad 10x5x3R Propeller About this productHQProp's MacroQuad propeller series was made for large drones that need agile and powerful flight characteristics. The tri-blade design and aggressive airfoil provide incredible thrust and power for those large drones that still want maneuverability.SpecificationsLength: 10"Pitch: 5"Blades: 3Hub Dia: 18mmHub Thickness: 9mmShaft: 9.5/5mmColor: BlackMaterial: Carbon Reinforced NylonWeight: 23.3g RX: TBS Crossfire Diversity Nano Rx - FPV LONG RANGE DRONE RECEIVERTeam BlackSheep Online Store - TBS Crossfire Diversity Nano Rx - FPV LONG RANGE DRONE RECEIVER (team-blacksheep.com)Yet again TBS is redefining long range flying! With the TBS Crossfire Diversity Nano RX we have taken the most powerful Crossfire receiver. Presenting the smallest full-fledged diversity receiver of any frequency, even boasting a power-redundancy circuit (battery not included!)True Diversity, Full range The TBS CROSSFIRE Diversity Nano Receiver is a compact R/C receiver with 8ch outputs (PPM, SBUS, and CRSF capable), with best-in-industry noise-rejection and record-breaking range capability. It is the only receiver to provide a true dual-input stage, chip-based diversity, with the usual filtering and noise rejection from onboard video systems.Beacon Mode Ever lost a plane and spent hours looking for it? Enter the TBS CROSSFIRE beacon mode. The diversity nano receiver comes with a LiPo battery port where you can connect an optional backup port (1s). It will keep the receiver running for a full day after all onboard electronics are gone. It will be screaming for help by giving you its GPS coordinates, and also blasting out RF beacon signals that will allow you to pinpoint its location even if no GPS was ever on your airplane. The backup battery (1s) will also be charged as soon as you apply power to the rig. Specifications Weight1.8g (receiver only)Size24mm x 18mmRequiresFirmware V2.87Input Power+3.3V to 8.4VI Installed 2 immortal t v2 antennas on the rx for better range

Price: 1650 USD

Location: Cumming, Georgia

End Time: 2024-10-07T15:36:22.000Z

Shipping Cost: 0 USD