Floor-lok Concrete Floor Sealer and Curing Aid Concentrate

Description: Floor-lok Concrete Floor Sealer and Curing Aid Concentrate Floor-lok Concrete Sealer , Curing Aid & Hardner Rainguard Floor-lok is a low cost water based silane siloxane penetrating concete floor sealer designed to aid concrete curing, sealing, hardening and dustproofing for both interior and exterior projects. Floor-lok protects concrete floors from damage caused by water intrusion and seepage, chloride ion intrusion, cracking caused by freeze/thaw cycles, spalling, and scaling and helps prevent efflorescence and lime run. It dries completely clear without leaving any surface film, change in looks or texture. Floor-lok contains a proprietary ingredient called Micro-Lok™. This additive ensures a long lasting mechanical bond and creates a hydrophobic barrier not affected by weathering, salt, dirt, freezing temperatures, UV light and wind-driven rain. Floor-lok is a penetrating sealer invisible after application as it penetrates completely below the concrete surface. It protects against damage from water, salt and freeze - thaw cycling that can cause cracks in a surface. It also adds stain resistance to the treated surface for easier cleaning. Using Floor-lok Concentrate offers a lower cost per gallon while being easier on the environment. One gallon of Floor-lok concentrate makes 10 gallons ready-to-use product. This means less product packaging, lower shipping costs and easier handling. It also means fewer containers to throw away and less jobsite waste. Where is Floor-lok used? Construction & Remodel Projects: Warehouse|factory|parking garage floors, building ramps, sidewalks, concrete decks Homeowner projects: Driveways, garage floors, patios, porches, walkways Why Floor-lok Curing Aid and Sealer? Warranty available for 1 year Easy to use Concentrate 100% Eco-friendly: low VOC Stain resistant to oil, gas and anti-freeze Floorlok does not alter surface appearance & UV resistant - will not yellow Nationally specified by architects in CSI sections 09900 Comparison Chart of Concrete Sealers by ConcreteNetwork.com TECHNICAL INFORMATION Color Clear, No change in appearance or surface texture Sheen/Gloss Level None Dry To Re-Coat 30-60 Minutes #Coats Recommended 1 (2 coats if especially porous) Back in-service time 1-2 hours walk or drive on Application method Low pressure hand pump or airless sprayer Where Can it be Used All Interior|Exterior horizontal unpainted concrete surfaces Apply to New Concrete 48 hours Low Application Temperature 35F|1.7C Surface & Air Base Water VOC Content <15 g/L Use on Material Concrete Warranty Available 1 year warranty available – download warranty application to register, see DOCUMENTS tab above CERTIFICATION/TEST Leed 4.2 (1) point credit available Meets LEED and SQAMD low VOC requirements ASTM E84 Surface Burning Flame spread 0, smoke developed 0 ASTM C309 Type 1, Class A&B for curing compounds COVERAGE RATE SQUARE FEET/GALLON Fresh Concrete 300 – 500 Newly Cured 200 – 400 Bare Concrete 200 – 400 Aged Concrete 150 – 250 Dustproofing Concrete 300 – 500 Floors to be Tiled 500 Lightweight Cocnrete 200 – 275 *Textured surfaces Decreases coverage rates Use of Temporary Heating Sources May result in 20% reduction of coverage rates APPLICATION INSTRUCTIONS CONDITIONS PRIOR TO APPLICATION Temperature (surface|air) 35F to 90F (1.7C to 35C) and at least 5F above dew point Moisture of substrate Less than 15% Humidity Less than 90% Rain No rain 48 hrs prior to, 12 hrs after application Cure time for newly poured concrete Apply 48 hrs after pour Application method Use low pressure hand pump or garden sprayer WORKING WITH CONCENTRATES PART # SIZE MAKES INSTRUCTIONS CR-1600 1 Gal 10 Gal Measure concentrate needed, mix with water, stir (use 9 parts water to 1 part Floor-lok) FOLLOW THESE SIMPLE APPLICATION STEPS 1. Floor-lok should be applied using low-pressure airless or hand pump spray equipment 2. Do not atomize material as it will negatively impact product performance. For power sprayers, use large tip size of at least .035 to .051. For hand pump sprayers, turn spray nozzle at end of the spray wand so product flows out more like a steady stream and keep pressure up to make sure enough material is coming out. Apply until surface is completely saturated and pooling occurs. Do not need to backroll or sweep off excess if absorption takes place within 1-2 minutes. 3. Avoid application in windy weather. 4. Trigger gun off at the end of each pass to avoid using excessive materials. Stop all applications only at corners, joints, seams, or edges. 5. Multiple coats may be applied, whiting or yellowing will not occur. A second coat is best applied "wet on wet" which means apply when first coat is damp but not yet dry. Use same flood coat procedure. PRECAUTIONS & LIMITATIONS 1. All surfaces to be coated should be clean of any dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mortar, and mold and mildew, etc. 2. All cracks should be pointed or caulked. All voids, bee holes, masonry surface defects and openings such as conduits, pipes, drains, door frames, vents, air conditioner openings, electrical openings, control joints, or any dissimilar materials should be repaired using urethane or other approved patching. STORAGE Store materials in a well-protected area between 45° and 90°F. Avoid freezing temperatures, direct sunlight, and moisture. Keep away from heat sources. Size Price Concentrate: Make 10 Gallon 205.85 Shipping Shipping cost:No cost shipping lower 48 US States FedEx Ground Delivery time:Typically 3-5 days to process order plus 1 to 5 days transit time after shipment depending on location Payment We accept the following payment methods: PayPal payment due at time of order placement Please contact us if you have any questions. Service PLEASE CONTACT CUSTOMER SERVICE FOR QUESTIONS

Price: 205.85 USD

Location: Costa Mesa, California

End Time: 2025-01-18T00:54:19.000Z

Shipping Cost: 0 USD