Description: E444X Polyaspartic High Gloss Concrete Floor Coating | 84% High Solids | Non-Yellowing | Low Odor E444X Polyaspartic Coating 84% High Solids | Non-Yellowing | Low Odor E444X Polyaspartic is a two component, 84% high solids, high gloss solvent, low odor high performance polyaspartic. E444X is aliphatic (non-yellowing) designed as an extremely tough, durable decorative topcoat with excellent adhesion to protect high performance epoxy floor concrete coating systems. E444X offers excellent abrasion and chemical resistance, is UV Stable, and has a beautiful, extremely clear, high gloss appearance available in 13 colors. With a 15-20 minute working time E444X can be recoated in 6-9 hours and take light foot traffic within 24 hours. E444X is sold in 32 oz quart, 2 gallon and 10 gallon kits. It comes in clear or can be tinted with one of 13 colors ( Pigment Sold Separately ). The spread rate of the E444X ranges from 133-320 square feet per gallon (5-12 mils dry film thickness) depending on project requirements. The E444X can also be applied as a clear or colored topcoat over an epoxy system AND direct to properly prepared concrete as a basecoat coating. PRIMER: Recommended as topcoat to high performance epoxy systems including E707HB Epoxy , however can be applied direct to concrete. TOPCOAT: None recommended. Can apply multiple coats of E444X. Where is E444X Fast Cure Polyaspartic used? Concrete floors Garage Floors Basement Floors Warehouse and commercial office floors Kitchens Outdoor Applications Why E444X Polyaspartic? Tough, durable topcoat for epoxy floor coatings Indoor and Outdoor Application Can be Applied Direct to Concrete High solids 84% Easy to work with 1:1 mix ratio Can be applied up 12 mils thick one coat (133 sq'/gallon) Excellent chemical and abrasion resistance UV Stable and will not yellow Mild Solvent Odor (compared to similar coatings) Beautiful high gloss appearance Designed for high traffic and industrial areas Available in clear & 13 colors (Colored Pigment Sold Separately) Beautiful Color Line To Enhance Your Flooring Projects. Our Polyaspartic Pigment Is Sold In 8 Oz and 16 oz sizes. Easy To Use, Just Pour And Blend. Add 5-6 Oz Per Mixed Gallon Of Liquid, Depending On Desired Color when the E444X is used as basecoat in full flake system and 8 oz per gallon when used as a basecoat in a solid color or less than full flake system. SPECIFICATIONS Solids By Weight 84% By Volume 83% VOC <90 g/L Colors Clear (Gardner) + 13 colors. See color chart Recommended Film Thickness 6 - 12 mils wet Coverage per Gallon 133-320 sq'/gal Packaging 2 & 10 Gallon Kits Mix Ratio 1:1 By Volume Self Life 6 months in unopened container Finish High gloss >80 at 60 degrees Abrasion Resistance Taber abrasion CS-17 calibrase wheel with 1000g total load & 500 cycles= 15 mg loss Application Temperature 50-90 Degrees F (relative humidity below 85%) Viscosity <500 centipose typical Ultimate Elongation 2.4% Compressive Strength 11,500 psi @ASTM D695 Tensile Strength 3,800 psi @ASTM D638 Hardness Shore D=55-60 COVERAGE RATE Coverage Per Gallon 133-320 Sq’/Gal CURE SCHEDULE (70°F) Pot Life - 150 gram mass (Actual usable working time is 15-20 minutes) > 2hours Tack free (dry to touch) 4-8 hours Recoat or topcoat 6-9 hours Light foot traffic 24 hours Full cure (heavy traffic) 2-7 days APPLICATION TEMPERATURE: 50-90 degrees F with relative humidity below 85% Chemical ResistanceRating Xylene C 1,1,1 Trichloroethane B MEK A Methanol B Ethyl Alcohol B Skydrol C 50% Sodium Hydroxide E 10% Sulfuric Acid C 10% HCI (aq) C 5% Acetic Acid C Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour immersion, E - long term immersion. MIXING AND APPLICATION INSTRUCTIONS PRODUCT STORAGE: Product must be stored in an area that will bring the product to room temperature prior to using. Continuous storage should be between 60 and 90 degree F. Keep from freezing. SURFACE PREPARATION: Preparation methods may vary depending on the system being applied. For a complete system thickness that is higher than 10 mils dry, a fine brush blast (shot blast), is recommended. To assure a trouble free bond, all dust, oil, dirt, foreign contaminants and laitance must be removed. It is recommended to perform a moisture test to determine that the concrete has an appropriate vapor barrier. This can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. Once 24 hours has passed, and the substrate is still dry below the plastic sheet, then the substrate does not show signs of eventual hydrostatic pressure problems that may later cause disbonding. This test does not guarantee, however, that there may not be future hydrostatic pressure issues in the future. PRODUCT MIXING: This product has a mix ratio of 1 part A to 1 part B by volume. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The material in the transfer pail is now ready to be applied on the properly prepared surface. Improper mixing may result in product failure. For best mixing results and proper blending of parts A and B, recommend a Jiffy Mixer style drill mixer. Use of an improper drill mixer can result in curing problems if the hardener also called activator (Part B) is not thoroughly blended with the resin (Part A) which can cause some areas on your floor to remain soft and not harden properly. DO NOT USE A PAINT MIXER. Most mixing problems described above can be traced back to using a paint mixer.. DO NOT HAND MIX as this approach can result in the same problems as using a paint mixer. PRIMING: A suitable primer should be used before applying this product. See the front side of this technical data for primer information. However, whether a primer is used or not, it is advisable to apply a test patch prior to using this product to determine if the adhesion characteristics are suitable for the service environment. PRODUCT APPLICATION: The mixed material can be applied by brush, serrated squeegee, or roller. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. The product can be used as a topcoat to seal in the broadcasted paint chip or broadcasted quartz base for the final coat. Use an air release roller tool when needed. Improper mixing may result in product failure. It should be pointed out that relative humidity can have a dramatic influence on the curing characteristics. The product will dry quicker and have less working time when the relative humidity is higher while a lower relative humidity will lengthen the dry time and working time. Mix only an amount that can be applied in the time allotted. Be sure that any tie-ins to previously applied material is also within the recommended time allotted for use as the previously applied material may begin to tack off in a short period of time RECOAT OR TOPCOATING: This material can be applied in multiple layers to increase build or can also be used as the final topcoat to seal in the aggregate filled base system. If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. Refer to the cure schedule as a guideline to follow, however it is best to test the coating before recoating or topcoating. This is done by pressing your thumb on the coating to ensure a fingerprint impression is not visible. If there is no impression visible, then coating the floor can be done. Note, colder temperatures require longer cure times before product can be recoated. Prior to coating the floor, make sure there are no contaminants exist. If contaminants or a blush exists, remove with a standard detergent cleaner and ensure floor is clean and dry prior to coating. CLEANUP/FLOOR CLEANING: Use Xylol for cleanup. Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested. RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, surface may be slippery, especially when wet or contaminated; keep surface clean and dry. LIMITATIONS: Colors or gloss may be affected by high humidity, low temperatures, chemical exposure, or exposure to lighting such as sodium vapor lights. Installing product too thick may result in surface imperfections, bubbles, or product failure Do not expose this product to water until fully cured Substrate temperature must be 5°F above dew point All new concrete must be cured for at least 30 days Physical properties are typical values and not specifications Light or bright colors (white, safety yellow, etc. may require multiple coats or a suitable color coordinated primer to achieve a satisfactory hide Always apply a test patch to determine product suitability and adhesion performance for your proposed application method and procedures Colors may vary from batch to batch, therefore use only product from the same batch for an entire job Physical properties listed on this technical data sheet are typical values and not specifications. NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our product is manufactured to the specifications as stated her or in other publications. All other information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommenced herein is the sole responsibility of the user. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Uncured epoxy resins, polymers and their curing agents may be ALKALINE, TOXIC or BOTH, depending on the particular system. They may cause ALLERGIC REACTIONS or HYPERSENSITIVITY REACTIONS. BEFORE USING any material, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM. Size Price 1 Quart Trial Size Kit 74.75 2 Gallon Kit 276.00 10 Gallon Kit 1,259.25 Shipping Shipping cost:No cost shipping lower 48 US States FedEx Ground Delivery time:Typically 3-5 days to process order plus 1 to 5 days transit time after shipment depending on location Payment We accept the following payment methods: PayPal payment due at time of order placement Please contact us if you have any questions. Service PLEASE CONTACT CUSTOMER SERVICE FOR QUESTIONS
Price: 74.75 USD
Location: Charleroi, Pennsylvania
End Time: 2024-12-19T20:25:33.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
All returns accepted: ReturnsNotAccepted
Return policy details:
Sheen: High Gloss
Country/Region of Manufacture: United States
Custom Bundle: No
Product Material: Polyaspartic
Surface Applied To: Cement, Concrete
Type: Does not apply
Brand: Does not apply
Available Variations
Color: 1 Quart Trial Size Kit
Price: 74.75 USD
Available Quantity: 7
Quantity Sold: 1
Color: 2 Gallon Kit
Price: 276 USD
Available Quantity: 6
Quantity Sold: 0
Color: 10 Gallon Kit
Price: 1259.25 USD
Available Quantity: 6
Quantity Sold: 0
