DNA PERFORMANCE AIR FILTER

Description: DNA PERFORMANCE AIR FILTER - SERVICE KIT DNA PERFORMANCE AIR FILTER SERVICE KIT SUITABLE FOR CLEANING AND RE-OILING ALL SIMILAR COTTON BASED PERFORMANCE AIR FILTERS 1 X 270ml CLEANING FLUID 1 X 220ml FILTER OIL How to protect your vehicle Always use the DNA air filter oiled with the special DNA oil, never without oil Note - The DNA Filter comes pre-oiled from the factory Service the DNA filter every 10,000-25,000 km depending on the environment you are using the filter How to protect your DNA Performance Filter Always use the special DNA service kit Never use petrol, diesel, thinners, solvents, compressor air or high pressure water Never dry using hot air or near a heater Race use FOR ROAD RACING - Always use a factory pre-oiled and air flow tested DNA air filter for maximum performance. FOR OFF ROAD RACING - Use DNA sealing grease on the sealing surface of the filter, service and test the filter at least 2-3 days before the race meeting. FOR EXTREME CONDITIONS - Like desert racing or enduro racing, it is preferable to use a slightly over oiled filter that has been used 1-2 hours in practice Step 1 Bring the DNA bottle you would like to de-seal in front of you, together with a pair of LATEX gloves and a pair of pliers. You will need the pliers to de-seal the bottle and the latex gloves to avoid spilling the liquid on your hands. Unscrew the bottle cap and remove the special sealing gasket as well for re-using it after servicing your filter. Step 2 After you unscrew the bottle cap, you must take the pliers and grab the sealed top of the bottle. Please grab the sealing cap and a small amount of the bottle head. Pull the pliers up with enough force to remove the sealing cap but not hurt yourself. Step 3 After the de-sealing of the bottle, please close the bottle again with the supplied sealing gasket and tighten firmly. Cleaning the DNA Performance Filter using the special cleaner Remove the filter from your air box and vacuum or dry brush the dirty side Cut the tip of the DNA filter cleaner bottle and apply cleaner on the filter until it is completely soaked. Allow the cleaner ten minutes to dissolve the dirt Brush the filter under warm water using a soft brush. When all the dirt has been removed, rinse very well using warm tap flowing water flowing from the clean side towards the dirty side. Allow the filter to dry in open air. Repeat the procedure if your filter is not clean. Do not force it by using a heater or hot air Attention - Do not use petrol, diesel, thinners or other solvents, compressed air or high pressure water because you will damage the filtering media and void your warranty. DNA recommend during the servicing procedure that you wear LATEX gloves. Oiling the DNA Performance Filter using the special oil Cut the tip of the DNA air filter oil bottle and apply oil to the edge of every pleat, by moving slowly across the filter and resting the tip of the bottle on the edge of each pleat. Squeeze the bottle lightly to allow a uniform line of oil on the pleat edge. On large pleats over 20mm high, oil each pleat twice. It is not necessary to use all of the oil. Attention - Do not use engine oil or other oils that are not specially designed for your DNA air filter. Doing so couls clog or damage your filter. As a result, you will have low performance and void your warranty. Allow the oil to be absorbed by the cotton for at least one hour. Afterwards, check if the filter has a uniform light red colour. In case there are white sections, re-oil only these sections. If you apply excessive oil, do not worry, it will be drawn away by the air stream after 10-20km of road use. DNA PERFORMANCE AIR FILTER - SERVICE KIT DNA PERFORMANCE AIR FILTER SERVICE KIT SUITABLE FOR CLEANING AND RE-OILING ALL SIMILAR COTTON BASED PERFORMANCE AIR FILTERS 1 X 270ml CLEANING FLUID 1 X 220ml FILTER OIL How to protect your vehicle Always use the DNA air filter oiled with the special DNA oil, never without oil Note - The DNA Filter comes pre-oiled from the factory Service the DNA filter every 10,000-25,000 km depending on the environment you are using the filter How to protect your DNA Performance Filter Always use the special DNA service kit Never use petrol, diesel, thinners, solvents, compressor air or high pressure water Never dry using hot air or near a heater Race use FOR ROAD RACING - Always use a factory pre-oiled and air flow tested DNA air filter for maximum performance. FOR OFF ROAD RACING - Use DNA sealing grease on the sealing surface of the filter, service and test the filter at least 2-3 days before the race meeting. FOR EXTREME CONDITIONS - Like desert racing or enduro racing, it is preferable to use a slightly over oiled filter that has been uséd 1-2 hours in practice Step 1 Bring the DNA bottle you would like to de-seal in front of you, together with a pair of LATEX gloves and a pair of pliers. You will need the pliers to de-seal the bottle and the latex gloves to avoid spilling the liquid on your hands. Unscrew the bottle cap and remove the special sealing gasket as well for re-using it after servicing your filter. Step 2 After you unscrew the bottle cap, you must take the pliers and grab the sealed top of the bottle. Please grab the sealing cap and a small amount of the bottle head. Pull the pliers up with enough force to remove the sealing cap but not hurt yourself. Step 3 After the de-sealing of the bottle, please close the bottle again with the supplied sealing gasket and tighten firmly. Cleaning the DNA Performance Filter using the special cleaner Remove the filter from your air box and vacuum or dry brush the dirty side Cut the tip of the DNA filter cleaner bottle and apply cleaner on the filter until it is completely soaked. Allow the cleaner ten minutes to dissolve the dirt Brush the filter under warm water using a soft brush. When all the dirt has been removed, rinse very well using warm tap flowing water flowing from the clean side towards the dirty side. Allow the filter to dry in open air. Repeat the procedure if your filter is not clean. Do not force it by using a heater or hot air Attention - Do not use petrol, diesel, thinners or other solvents, compressed air or high pressure water because you will damage the filtering media and void your warranty. DNA recommend during the servicing procedure that you wear LATEX gloves. Oiling the DNA Performance Filter using the special oil Cut the tip of the DNA air filter oil bottle and apply oil to the edge of every pleat, by moving slowly across the filter and resting the tip of the bottle on the edge of each pleat. Squeeze the bottle lightly to allow a uniform line of oil on the pleat edge. On large pleats over 20mm high, oil each pleat twice. It is not necessary to use all of the oil. Attention - Do not use engine oil or other oils that are not specially designed for your DNA air filter. Doing so couls clog or damage your filter. As a result, you will have low performance and void your warranty. Allow the oil to be absorbed by the cotton for at least one hour. Afterwards, check if the filter has a uniform light red colour. In case there are white sections, re-oil only these sections. If you apply excessive oil, do not worry, it will be drawn away by the air stream after 10-20km of road use. × Buy now and save! Order Info 30 Day Returns Click the Shipping & Payments tab above the listing description for more info! PAYMENT Immediate payment is required upon selecting "Buy It Now" or by checking out through the cart. We accept payment via PayPal and all Major Credit Cards, Debit Cards & Google Pay. Thank you for shopping with us on eBay! Additional Information No additional information at this time Ask a question You might also like IXIL Hyperlow Dual Exit Silencer HONDA CBR125R 2011-16 IXIL L2X Hyperlow Full System - Honda MSX125 2021-23 IXIL Race Xtrem Carbon Full System Yamaha MT-09 / SP 2021-23 IXIL Black Full System Low mount Honda Monkey 125 2018-24 CUSTOMERS OUTSIDE OF THE UK: VAT will not be charged on your order. However, local taxes will be payable prior to or upon delivery. Motorcycle Performance Store are official UK Distributors of Termignoni, QD, Ixil, Ixrace and SC Project Exhausts, T800 UpMap Bluetooth tuning modules, Puig Motoplastics, and DNA Performance Air Filters. eBay integration by

Price: 34.82 GBP

Location: Gloucestershire, England

End Time: 2024-12-10T00:13:59.000Z

Shipping Cost: 22.88 GBP