5PCS Nema17 for 1.7A,4200g.cm,48mm length,2-Phases,0.9°,42BYGHM809 Wantai Motor

Description: Great News! for USA buyers ,Ship from USA warehouse, after payment, within 3-5 days for receiving products! No taxes from customs, no damage, better service, please don't hesitate! This item includes: 5 PCS CNC Nema 17 for 1.7A ,4200g.cm,48mm length,4-Lead,2 phase Bipolar Connection Stepper Motor 1, Stepper Motor Technical SpecificationsPart No.: 42BYGHM809Frame Size: NEMA17Step Angle: 0.9 degreeVoltage: 2.8VCurrent: 1.7 A/phaseResistance: 1.65Ohm/phaseInductance: 4.0mH/phaseHolding torque: 4200g.cm 60oz-in Rotor inertia: 68g-cm2Detent torque: 0.22g-cmNumber of wire leads: 4Weight: 0.34 kgLength: 48mmMotor shaft : 5mmFront shaft length: 20mm We offer customer’s designed service ! If you need special size , please offer us your size requirements ,so that we can manufacturer the exact models for you ,Thanks : ) if you need you may also choose the driver DQ420MA to drive this motor ,Thank you ! :) Matching Stepper Motor Driver DQ420MA with 1.7A , 12-36V/128 Microstep http://www.ebay.com/itm/Cheap-set-Cnc-1-7A-12-36VDC-128Micostep-Bipolar-CNC-digital-Wantai-motor-driver-/130839628888?pt=LH_DefaultDomain_0&hash=item1e76a64c58 Introduction : DQ420MA is a type of two-phase hybrid stepping motor driver, the drive voltage of which is from 12VDC to 36VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 20mm to 42mm outside diameter and less than 2.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor to run smoothly almost without noise and vibration. Holding torque when DQ420MA driver runs at high speed is also significantly higher than other two-phase drivers, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Features: l High performance, low price l Average current control, 2-phase sinusoidal output current drive l Supply voltage from 12VDC to 36VDC l Opto-isolated signal I/O l Over-voltage, under voltage, over-current, phase short circuit protection l 8 channels subdivision and automatic idle-current reduction l 8 channels output phase current setting l Offline command input terminal l Motor torque is related to speed, but not related to step/revolution l High start speed l High holding torque at high speed Electrical specification: Input voltage 12-36VDC Input current ＜ 2A Output current 0.44A- 2.83A Consumption Consumption：40W； Temperature Working Temperature -10～45℃； Stocking Temperature -40℃～70℃ Humidity No condensation, no water droplets gas Prohibition of combustible gases and conductive dust weight 70G 1. Pins assignments and description: 1) Connector Pins Configurations Pin Function Details PUL +,PUL- Pulse signal, PUL+ is the positive end of pulses input pin PUL- is the negative end of pulse input pin DIR+,DIR- DIR signal: DIR+ is the positive end of direction input pin DIR- is the negative end of direction input pin ENA+ Enable signal: ENA+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver. ENA- ENA- is the negative end of direction input pin. Usually left unconnected (enabled) We ship worldwide! More Order quantites, more discount!!! Our products are mainly used in robotization, Spinning Automatization, Printing, Packing, Medica Machine, Make-up Equipment, Communication, Household Appliance, Water Pump, Milling Machine, Engraver Machine, CNC Routers.. etc automatic equipment of various trades.

Price: 79 USD

Location: CA

End Time: 2024-10-19T12:55:14.000Z

Shipping Cost: 0 USD